Changed Map Sensor Still Getting Code In April 2021 my check engine light came on and it was P0106 and I replaced the MAP sensor The check engine light and code went away but I was still having issues with when I am stopped with my A C on my cars idle fluctuates a lot Randomly I would have little situations where I could feel it misfire Now the other day my check engine light is
This issue is not the MAP sensor but rather the mass air flow MAF sensor This sensor is usually missed unless the computer sees it malfunctioning Most of the time the MAF will get dirty and become ineffective and not work properly but be within the parameters of the computer system Check the MAF sensor and clean it out with dry air For the longest time it would not throw any codes until last week I was sitting at the light and it started idling like crap and the check engine like kicked on and I immediatly drove down to auto zone and had the code read out it was p0108 high maf sensor voltage I replaced the maf sensor and Im still having the same problems and it still
Changed Map Sensor Still Getting Code
Changed Map Sensor Still Getting Code
https://f01.justanswer.com/BrianP510/44bf79e5-ebb3-477a-97dd-73497291a40e_08gl450d.png
Can A Map Sensor Affect Your Gas Gauge CHM
https://commpic.communityheritagemaps.com/what_are_the_symptoms_of_a_map_sensor_going_bad.jpg
MAP Sensor Stolen 99 ML320 Mercedes Benz Forum
https://www.benzworld.org/attachments/missing-map-sensor-003-jpg.260084/
Upon having tested we were told the MAP sensor was bad Replaced the sensor today Unhooked the ground on the battery for more an thirty minutes to reset the check engine light The light is still on Took the car back to the auto parts store and they said the computer is still giving the same code even though the part has been replaced I have replaced the map sensor the purge valve the o2 sensors the catalytic converter and the pvv valve I taken my Yukon to the local GMC Deal for a diagnostic test but they said to start with the map sensor I replaced all the part and still my Yukon have a rough idle shaking and sounds like an exhausting leak
After replacing the PCM I am now getting a P0129 code when I turn on the key Replaced the MAP sensor but still get the code and it runs rough at idle and at 3800 RPM Funny thing is that when I disconnect the battery to clear the code and do a quick start with the key the code does not appear and the cars runs perfectly When I use my Luckily replacing a MAP sensor is rarely difficult plus you can first try cleaning it as that often helps The full list of symptoms of a faulty MAP sensor includes poor performance check engine light rough idle hesitation and difficulty starting the car The solution is to either clean or replace the MAP sensor
More picture related to Changed Map Sensor Still Getting Code
Replaced Knock Sensor And Still Getting Code P0332 Loomgear
https://loomgear.com/wp-content/uploads/2023/02/Replaced-Knock-Sensor-and-Still-Getting-Code-P0332.webp
08 Mercedes Gl450 Changed Crankshaft Sensor Still Getting Code P0339
https://f01.justanswer.com/BrianP510/567cc7cd-9a31-4ffd-b8bb-c580ee48b8ef_08gl450a.png
Map Sensor Cleaner
https://www.f150ecoboost.net/attachments/20180325_132859-jpg.138066/
Changed MAP sensor and still getting code 89 S10 Blazer 4 3 4x4 was getting a codes 24 33 44 45 I changed MAP reset computer All the other codes are gone but im still getting MAP code Save Share Reply Quote Like Sort by Oldest first Oldest first Newest first Most reactions R Rexxcastle Discussion starter 9 Replaced the MAP Sensor after getting code P0106 Cleared the code and it still comes back after I shut the car off and back on 2009 Kia Optima 2 4L but it turned off when we changed the spark plugs Ran the codes again a few days later and it was still showing as a pending code Replaced the sensor and all the codes went away and stayed
[desc-10] [desc-11]
08 Mercedes Gl450 Changed Crankshaft Sensor Still Getting Code P0339
https://f01.justanswer.com/BrianP510/35b13b10-516b-4560-a6e2-1d588d63c7a5_08gl450f.png
What You Need To Know About A MAP Sensor Technician Academy
https://technician.academy/wp-content/uploads/2019/01/MAP-sensor.jpg
Changed Map Sensor Still Getting Code - After replacing the PCM I am now getting a P0129 code when I turn on the key Replaced the MAP sensor but still get the code and it runs rough at idle and at 3800 RPM Funny thing is that when I disconnect the battery to clear the code and do a quick start with the key the code does not appear and the cars runs perfectly When I use my